2027 Peterbilt 567
Call For Price (804) 231-9800
This new 2027 Peterbilt 567 is built for construction material hauling. It’s powered by a 510 HP PACCAR MX-13 with 1,850 lb-ft of torque and an Allison 4500 RDS 6-speed automatic. Three Watson-Chalin self-steering pusher axles join a 46,000 lb Dana Spicer tandem for an 85,000 lb GVWR. It carries a Heritage aluminum material hauler body with an Aero electric tarp. It’s finished in black and backed by PACCAR MX and Peterbilt factory coverage. Contact us to learn more about this unit.
- Stock Number:
- VD 850608
- Model:
- 567
- Location:
- The Peterbilt Store - Richmond
Overview
Overview
This new 2027 Peterbilt 567 conventional day cab is configured as a six-axle construction dump truck built to haul construction materials in on/off-highway service. It is upfit with a Heritage aluminum material hauler end dump body and three self-steering pusher axles, and it carries an 85,000 lb GVWR.
Engine & Drivetrain
The truck is powered by a PACCAR MX-13 rated at 510 HP at 1,600 RPM, governed at 2,200 RPM, with 1,850 lb-ft of torque at 1,000 RPM. The engine is 2024-emissions and CARB compliant. The powertrain is optimized for performance, with a typical operating speed of 65 MPH.
It is equipped with a PACCAR compression brake, with controls on the right-hand column, and a PACCAR 160-amp brushed alternator. Additional equipment includes a PACCAR premium starter, three PACCAR AGM 12V batteries rated at 2,775 CCA, and a low voltage disconnect system. The engine also has a 110–120V immersion block heater, a 2-speed fan clutch for frequent start/stops, a WABCO 37.4 CFM air compressor, and a high-efficiency cooling system. Air intake runs through dual self-cleaning under-hood pre-cleaners and a firewall-mounted air cleaner. Fuel passes through a PACCAR fuel/water separator with an extended service interval.
Exhaust is a dual SOC setup with a left-hand stack and the DPF/SCR module mounted under the cab on the right side. It finishes in a 7" chrome-plated, 36" tall standpipe with a 45-degree curved cut tip. A 12-pin remote PTO/throttle provision is located in the engine bay, and the engine idle shutdown timer is disabled.
Transmission
The engine is paired with an Allison 4500 RDS-P Gen 6 Rugged Duty Series automatic in a 6-speed configuration with a TC-571 torque converter. It shifts through a dash-mounted push-button shifter. Auto neutral activates with the parking brake, and neutral-at-stop is enabled. Power flows through an SPL170 HD-XL driveline with two midship bearings and an SPL170 XL interaxle driveline to a 4.10 rear axle ratio. A dash-mounted single-acting electric-over-hydraulic PTO control is included.
Chassis & Axles
The wheelbase measures 312". Bumper-to-front-axle is 86.2", cab-to-axle is 225.8", and cab-to-end-of-frame is 290.8". The frame uses 11-5/8" steel rails at 3/8" thickness to 444", with a 3/4-length steel inner liner. The rails are zinc-coated and anti-corrosion treated, with aluminum crossmembers and heavy-duty iron front spring brackets. Two Holland TH-10050 tow hooks sit at the end of the frame. Up front are a heavy-duty external tow eye and a chromed, deep tapered steel bumper with two tow points.
The front axle is a PACCAR FX-20 wide-track steer axle rated at 20,000 lbs with a 4" drop. Steering is a Sheppard HD94 dual-gear power steering system with a frame-mounted reservoir and cooler.
The rear axle is a heavy-wall Dana Spicer D46-172 tandem rated at 46,000 lbs. It has a tandem differential lock with speed interlock, and all axles run synthetic lubricant.
Three Watson-Chalin SL13 self-steering pusher axles are rated at 13,500 lbs each and include three dedicated air tanks. They are spaced 48", 96", and 144" from the centerline of the forward drive axle. Lifted axles stow higher to maximize ground clearance. They are controlled by frame-mounted regulators with switches and gauges in the dash.
Engineering-assigned ratings are an 18,740 lb front GAWR and intermediate GAWRs of 11,020 lbs and 23,000 lbs. The rear GAWR is 23,000 lbs, and the GVWR and GCW are both 85,000 lbs. The maximum grade rating is 6%.
Brakes & Safety Systems
Bendix ADB22X air disc brakes are fitted front and rear on PHP10 Preset+ hubs. The truck has Bendix ESP Electronic Stability Program with automatic traction control, along with a dash switch to deactivate traction control. It also carries a 6S6M anti-lock braking system and a tire pressure monitoring system. The air system includes a Bendix AD-HF EP heated air dryer with a coalescing filter and extended purge, plus painted steel air tanks with pull cords. A pneumatic park brake and an SBM valve are also included.
Suspension
The rear suspension is a Hendrickson HMX EX 460 HaulMaax rated at 46,000 lbs with a 54" axle spread and a 70K creep rating. It has dedicated shock absorbers and a 17.5" saddle height. The front suspension uses 20,000 lb taper leaf springs with Tenneco shocks and greasable spring pins.
Cab & Interior
The cab is a 115" BBC aluminum vocational day cab with a Metton hood and a stainless steel crown and grille with tilt assist. It includes thermal insulation and cab air suspension. The interior is finished in the Prestige package in Sterling Gray.
The driver rides on a Peterbilt LX premium air-ride high-back seat in black Mordura with a right-hand armrest. The passenger has a Peterbilt ST high-back seat in black Mordura with a left-hand armrest and a toolbox underneath. The multi-function steering wheel carries audio and cruise controls and sits on a tilt/telescoping column.
Instrumentation centers on a 15" digital cluster. It displays engine and transmission oil temperatures, turbo boost, engine percent torque, air filter restriction, and brake application pressure. Additional 52mm backlit gauges monitor front and rear drive axle oil temperatures, fuel filter restriction, and all three pusher axle pressures. Three additional dash switches are pre-wired.
For audio and communication, the cab has a ConcertClass AM/FM/weatherband radio with 3.5mm aux, a four-speaker midlevel package, Bluetooth phone and audio, and a USB port. A Uniden Bearcat 880 CB radio with weatherband is mounted in the header with a low left-cowl antenna. Global telematics hardware is installed.
The cab has power door locks and windows, a combination fresh air heater and air conditioner, and a one-piece curved windshield. Windows have dark tint, and the rear glass is a fixed one-piece window. Bright-finish Peterbilt aero mirrors are motorized and heated with integrated convex lenses, and a look-down mirror sits over the passenger door. A stainless steel outside sunvisor and twin 23" roof-mounted round Peterbilt air horns complete the exterior. The cab also includes a removable bug screen behind the grille, intermittent wipers, a deep rear-wall map pocket, and an NFPA-compliant exterior grab handle. Safety equipment includes a fire extinguisher, a triangle reflector kit, and a 107 dB backup alarm.
Lighting & Electrical
Lighting includes projector headlight pods with fender-mounted turn signals, five LED bullet marker lights, and two bracket-mounted load lights. Turn signals are self-canceling. Switches and wiring are provided for fog lights, beacon/strobe lights, and auxiliary under-cab lighting.
Fuel & Tanks
The truck carries a polished 26" aluminum 110-gallon fuel tank under the cab on the left side, with a polished non-slip step and polished tank straps. The DEF tank is mounted on the left behind the cab with a polished stainless cover. A polished aluminum battery box sits above the rails behind the cab, and a non-slip aluminum aftertreatment cab entry step is included.
Body & Equipment
The body is a Heritage aluminum material hauler, 96" wide, with 54" sides plus a 6" board. The sides, side posts, and dirt shedders are 3/16" material with an enhanced finish, topped by a 9" extruded top rail with 2" x 6" boards on each side.
The floor is 1/4" up front and 3/8" in the last 120". It is supported by 6" I-beam longsills with rubber cushions and 3-1/2" extruded boxed crossmembers on 12" centers. The bottom rail has radius cleanouts.
The 3/16" radius bulkhead has a man door, and its top is squared off so the tarp mounts flush. No cab shield is fitted. An access step and an aluminum diamondplate deckplate between the tank and the body provide access to the man door.
The 60" overslung tailgate is 1/4" thick with a 3" slope and two panels with horizontal bracing. It is air-operated and comes with tailgate chains, a center coal door, and salt locks on each side.
The hydraulic system uses a pin-to-pin telescopic front hoist with a Hotshift PTO for the Allison automatic. It runs a direct-mount pump with a shifter valve, controlled by a feathering valve with air control. A tower between the seats houses the body, strobe, and tarp controls, and a pump kickout switch is installed. Hydraulic fluid is held in a 35-gallon aluminum upright tank behind the cab. The 3-line system has shutoff valves, and the dash includes PTO-engaged and body-up indicator lights.
Body lighting is an LED package. Combo stop/turn/tail lights are set in the rear posts, and marker lights sit at the top and bottom of every post. Two front marker lights and two front strobes are mounted in front of the tarp wind screen, and there is a strobe in each rear post. On the chassis, round combo lights are mounted in the plate and the ID cluster sits on the hinge.
The tarp is an Aero electric arm flip system in asphalt, with the wind screen mounted flush to the front of the body. A pull-out ladder is built into the driver’s-side front panel below the bottom rail, with inside steps at the front. A shovel holder is mounted at the front of the body on the driver’s side, and an 8" bolt-on apron is fitted at the rear. Heritage 30" front mud flaps with anti-sail brackets sit ahead of the lift axle, and full-width Heritage flaps run across the rear. The body front is squared, with body fenders built to cover the lift axle. Full-height side liners are installed at the rear of the body. Rear tow hooks and a body prop are included. The body carries an enhanced finish, and the boards are painted to match the cab.
Paint
The cab, hood, hood top, cab roof, and fenders are finished in Axalta two-stage metallic/pearl black over a black frame.
Tires & Wheels
Front tires are Bridgestone M864 385/65R22.5 18-ply on Accuride 22.5 x 12.25 aluminum wheels with a 2.88" inset. The tandem drive axles run eight Bridgestone M863 11R22.5 16-ply tires on Accuride 22.5 x 8.25 aluminum wheels. The pusher axles carry six Continental HSR2 SA 255/70R22.5 16-ply tires on Accuride 22.5 x 8.25 aluminum wheels. All wheels are extra-polished, and wheel guards are fitted to the steer, tandem, and pusher axles.
Warranty & Protection
This new truck is backed by Peterbilt Class 8 standard coverage of 1 year/100,000 miles (160,000 km). PACCAR MX standard engine coverage runs 2 years/250,000 miles (400,000 km)/6,250 hours, and the base emissions warranty is 5 years/100,000 miles. A 5-year SmartLINQ remote diagnostics and over-the-air subscription for the PACCAR MX engine is also included.
Specifications

Estimate Your Monthly Payment
Use our online tool to get an estimated monthly payment and see how different financing options can impact your bottom line.
Our Experienced Finance Team is Here to Help
We work with a network of lenders to secure the most competitive rates available.
Fast and Easy Approvals:
Get the green light quickly so you can focus on running your business.
Expert Guidance:
Our knowledgeable finance professionals will guide you through every step of the process.
